Powerline analyser SHARK 100-S

ElEctronic SubmEtErS with wiFi EthErnEt capability

Image: Shark 200-S meter promotion: data-logging software graph, office buildings and a shopping centre, and the meter with Wi-Fi antenna showing 120.0.

Shark^®200-S Meter

Image: Shark 100-S economical WiFi submeter for real-time monitoring and a Shark 200 meter, both with red LED displays showing 120.0 on phases A, B and C.

Shark^® 100-S Economical WiFi Submeter Real Time Monitoring Only

induStry lEading tEchnology

High Performance Metering Technology

Image: cULus Listed mark for electrical and electronic measuring and test equipment.

0.2% Accuracy Class — Highly Accurate
Revenue Certifiable Test Pulse with KYZ Output

Shark® 100-S only

IEEE 802.11 Wireless Ethernet Capability
10/100BaseT Ethernet - RJ45

Shark^® 200-S Advanced Datalogging WiFi Submeter Onboard Logging, Automated Billing

Modbus RS485 or Modbus TCP
For Commercial Building, Industrial and Shopping Mall Applications
2 Megabytes Flash Memory for Extensive Datalogging (Shark® 200-S Submeter)

Image: CE marking and ISO 9001:2000 certification mark.

Feature Summary

Image: Shark 200 power meter with three red LED readings of 120.0 and an antenna for wireless communication.

0.2% Class Revenue Certifiable Energy and Demand Submeter
Meets ANSI C12.20 (0.2%) and IEC 687 (0.2%) Classes
Multifunction Measurement Capability
Bright Red LED Display with three .56" lines
% of Load Bar for Analog Meter Perception
Ethernet or Wireless Ethernet (Modbus TCP)
Serial RS485 Communication (Modbus RTU/ASCII)
Direct Interface with Most Building Management Systems
Very Easy To Install
Extensive Datalogging and Alarm Recording (Shark® 200-S Submeter)

Image: Interior of a busy multi-storey shopping centre, an example of a commercial building application.

Highly Accurate Metering, Simple Communication Technology

Applications

Industrial Submetering
Universities
Commercial Buildings
Government Facilities
Shopping Malls
Military
Energy Efficiency OEMs
Airports

Introduction

Electro Industries introduces the most advanced series of electrical submeters available. These high performance products measure revenue grade electrical energy usage and communicate back information using RS485, RJ45 Ethernet or IEEE 802.11 WiFi Ethernet connections. Place a unit anywhere within a facility and it can communicate back to central software quickly and automatically.

The units use standard 5 or 1 amp CTs (either split or donut). They surface mount to any wall and are easily programmed in minutes.

Image: Use Ethernet or WiFi to easily meter any facility

V-Switch™ Technology Measurement Upgrade Packs

The Shark® 100-S/200-S submeters are equipped with EIG’s exclusive V-Switch™ technology, a virtual firmware-based switch that allows you to enable meter features through communication, even after installation. Using V-Switch™ keys, you can purchase what you require now and field upgrade functionality as needed. This allows you to optimize your metering investment. Begin with a simple energy billing submeter and upgrade it to a full functioning energy billing meter with power quality and alarm measurements.

Shark^® Series Submeter Accuracy (Class 10)

Measured Values	Accuracy
Voltage L-N	0.1% of Reading
Voltage L-L	0.1% of Reading
Current	0.1% of Reading
+/- Watts	0.2% of Reading
+/- Wh	0.2% of Reading
+/- VARs	0.2% of Reading
+/- VARh	0.2% of Reading
VA	0.2% of Reading
VAh	0.2% of Reading
PF	0.2% of Reading
Frequency	0.03Hz
%THD (Shark® 100-S only)	5.0 %
Load Bar	+/- 1 Segment

Traceable Watt-Hour Test Pulse for Accuracy Certification

To be certified for revenue metering, power providers and utility companies need to know that the billing energy meter will perform to its stated accuracy. To verify the meter’s performance and calibration, power providers use field test standards to insure that the unit’s energy measurements are correct. Since the Shark® 100-S/200-S submeters are traceable revenue meters, they contain a utility grade test pulse allowing power providers to verify and confirm that the meters are performing to their rated accuracy. This is an essential feature required of all billing grade meters.

Available V-Switches:

V3 (100-S only) – Volts, Amps, kW, kVAR, PF, kVA, Freq. kWh, kVAh, kVARh
V4 (100-S only) – Volts, Amps, kW, kVAR, PF, kVA, Freq. kWh, kVAh, kVARh, %THD Monitoring and Limit Exceeded Alarms
V33 (200-S only) – Volts, Amps, kW, kVAR, PF, kVA, Freq. kWh, kVAh, kVARh, 2 Megabytes Datalogging memory and Limit Exceeded Alarms. Note: The Shark® 200-S submeter does not have an upgrade for harmonic measurements.

Generate Cost Allocation and Billing

Using Electro Industries’ E-Billing EXT™ software, you can track energy usage data to provide utility bills for usage and demand. You can also customize rate structures and aggregate multiple meters for billing. E-Billing EXT™ produces bills utilizing either Energy Manager HMI logging or from data stored in Shark® 200-S logs. For simple bill generation we highly recommend using the Shark® 200-S submeter with internal logging.

Lower demand cost
Provide meter billing services
Provide user accountability for actual usage

Image: Excel spreadsheet with an energy usage report for a hydro cracker plant: monthly energy usage in kWh, cost in USD, demand and peak demand for the current and last month.

Utility Peak Demand Metering

The Shark® 100-S/200-S submeters provide user-configured Block Window or Rolling Window Demand. This allows you to set up a particular utility demand profile. Block Window Demand is demand used over a fixed user-configured demand period (usually 5, 15 or 30 minutes). Rolling Window Demand is a fixed window demand that moves for a user specified sub-interval period. An example is a 15-minute demand using 3 subintervals, providing a new demand reading every 5 minutes based on the last 15 minutes. Readings for kW, kVAR, kVA and PF are calculated using utility demand structures. Other parameters offer max and min capability over the user-selectable averaging period. Voltage provides a non-rolling instantaneous max and min reading, displaying the highest surge and lowest sag seen by the meter.

Advanced Communication Capability with IrDA Interface

Image: Laptop showing a phasor diagram communicating wirelessly with a power meter that has an antenna.

Standard Modbus RS485 Communication

IrDA Port

Standard communication includes an RS485 output speaking Modbus protocol. This allows the unit to be connected to any serial RS485 bus using the Modbus interface. The unit communicates easily with most building automation or other software systems. Baud rates are up to 57.6K baud to provide fast update times.

Use an IrDA-equipped laptop PC to program and read the Shark® 100-S/200-S submeter.

KYZ Pulse

WiFi or Land Based Ethernet

For applications in which a pulse is needed, the unit also provides a KYZ output which pulses proportional to the amount of energy consumed. This feature is used for pulse counting applications or for building management systems where serial or Ethernet protocol is not available.

The unit offers two Ethernet options — either an RJ45 or WiFi connection. The WiFi option allows the 100-S/200-S submeter to be used on standard WiFi base stations. The unit is assigned an IP address; it communicates Modbus protocol over Ethernet TCP/IP.

Image: EIG meter with LED display reading 120.0, wireless antenna, IrDA port and load bar; the open housing shows measurement circuitry, Wi-Fi Ethernet, RJ45 Ethernet/Modbus TCP, KYZ pulse and RS485 Modbus outputs, and voltage and current connections.

Superior Ethernet Simplifies Meter Connectivity

These submeters harness the latest Ethernet technology by providing a simple, over-the-counter wireless architecture. The submeter communicates over any existing wireless or wired Ethernet infrastructure. Just install the unit, plug in its IP address, and the device automatically connects to your LAN wirelessly. You can extend the network simply by adding WiFi access points. Wireless Ethernet is reliable and easy to integrate, making it the superior solution for mass meter deployment.

Benefits of Wireless Ethernet over Dedicated 900 MHz Spread Spectrum

Standard Infrastructure (No Dedicated Hardware)
Low Cost to Deploy and Expand
Superior Speed Over Dedicated Wireless Networks
Significantly Easier to Configure and Maintain
Standard Modbus TCP Data Stream
Can Be Easily Integrated Through the Internet

Image: Shopping mall application: Shark submeters in each store send data over IEEE 802.11 Wi-Fi to Wi-Fi base Ethernet access points, so PC software can read the meters from anywhere on the network.

WiFi Ethernet — the simplest way to implement a fast, reliable metering project

Shark® 200-S Advanced Logging Features

Extensive Datalogging Capability

The Shark® 200-S submeter has 2 Megabytes of Flash memory that give it extensive datalogging capability. The 200-S offers three Historical logs, a Limits (Alarm) log, and a System Events log. The unit has a real-time clock that allows for time-stamping of all the data in the instrument when log events are created.

Historical logs:

Each of the three historical logs can be programmed with unique parameters consisting of any measured reading. Up to 64 parameters can be recorded per log.

Image: Historical Trending

Limits (Alarm) log:

The Limits log provides magnitude and duration of an event. 2048 events are available; the log provides time-stamp and alarm value.

System Events (anti-tampering) log:

To protect critical billing information, the meter records and logs the following with a time stamp:

Demand/Energy/Log resets
Password requests
System startup
Log reads
Changes to meter’s programmable settings

Image: Software window with a list of logged records in rows, with date and time columns and some status cells highlighted in colour.

Alarm Log

Dimensional Drawings

Image: Dimension drawings of the wireless unit: rear mounting plate 5.95 in (15.1 cm) wide, front 7.53 in (19.1 cm) wide by 7.90 in (20.1 cm) high, side depth 3.11 in (7.9 cm), antenna 4.4 in (11.2 cm).

Installation

Image: Open for Installation

Close for Operation

Wiring Diagrams

Image: 3 Phase 3 Wire Delta Direct

3 Phase 3 Wire Delta with PTS

Specifications

Voltage Inputs

20-416 Volts Line To Neutral, (Shark® 100-S meter), 20-576 Volts Line to Neutral (Shark® 200-S meter)
0-721 Volts Line to Line
Universal Voltage Input
Input Withstand Capability –
Meets IEEE C37.90.1 (Surge
Withstand Capability)
Programmable Voltage Range to Any PT ratio
Supports: 3 Element WYE,
2.5 Element WYE, 2 Element Delta, 4 Wire Delta Systems
Burden: 0.36VA per phase Max at 600V, 0.014VA at 120 Volts

Current Inputs

Class 10: 5 Amp Nominal, 10 Amp Maximum
Class 2: 1 Amp Nominal, 2 Amp Secondary
Programmable Current to Any CT Ratio • Burden 0.005VA per phase Max at 11Amps
5mA Pickup Current for Class 10
1mA Pickup Current for Class 2
Current Surge Withstand: 100A/10 Seconds at 23° C
Isolation
All Inputs and Outputs are galvanically isolated to 2500 Volts AC.
Environmental Rating
Storage: (-20 to +70)° C
Operating: (-20 to +70)° C
Humidity: to 95% RH (Non-condensing)

Sensing Method

RMS
Sampling at 400+ Samples per Cycle on all channels measured readings simultaneously
Harmonic %THD (% of Total Harmonic Distortion) - Shark® 100-S meter only

Update Rate

Watts, VAR and VA - Every 6 cycles (e.g., 100ms @ 60Hz)
All other parameters - Every 60 cycles (e.g., 1s @ 60Hz) (1 second for Current Only measurement, if reference voltage is not available)

Power Supply

90 to 400) Volts AC and ( (100 to 370) Volts DC. Universal AC/DC Supply • Burden: 16VA max.
Communication Format
2 Com Ports
RS485 Port
IrDA (Through Faceplate)
Protocol Modbus RTU, Modbus ASCII
Com Port Baud Rate: (9600 to 57,600)
Com Port Address: 0-247
8 Bit, No parity
Modbus RTU or ASCII Protocols

Ethernet

802.11b Wireless
10BaseT Ethernet (RJ45) • Modbus TCP Protocol
Dimensions and Shipping
Weight: 4 lbs
7.9H x 7.5W x 3.1D in 20.1H x 19.1W x 7.9D cm

Meter Accuracy

See page 3

Compliance:

IEC 687 (0.2% Accuracy)
ANSI C12.20 (0.2% Accuracy) • ANSI (IEEE) C37.90.1 Surge Withstand
ANSI C62.41 – Burst
IEC1000-4-2 – ESD
IEC1000-4-3 – Radiated Immunity
IEC 1000-4-4 – Fast Transient • IEC 1000-4-5 – Surge Immunity • UL Listed (Shark 100-S only)

Ordering Information

To order, please fill out ordering guide:

Image: * Shark® 100-S meter only

	Model		Frequency		Current Class	V-Switch TM Pack	Communication Format
Option Numbers:		- -		- -		-	- -
Example: Sh	hark® 100-S	-	60	-	10	- V3	485 -
	Shark® 100-S		50 50 Hz System		10 5 Amp Secondary	V3* Default with Energy Counters (Shark® 100-S)	485 RS485
	Shark® 200-S		60 60 Hz System		2 1 Amp Secondary	V4* Above with Harmonics and Limits (Shark® 100-S)	WiFi Wireless or LAN Based Ethernet
Shark® 100-S Shark® 200-S	S meter only S meter only					V33** Multi-Function Meter with 2 MB Datalogging Memory (Shark® 200-S)

** Shark® 200-S meter only

Additional Accessories

Communication Converters

CAB 6490 – USB to IrDA Adapter for Programming Unicom 2500 – RS485 to RS232 Converter Unicom 2500-F – RS485 to RS232 to Fiber Optic Converter Modem Manager, Model #, MM1– RS485 to RS232 Converter for Modem Communication

CT400K – 400/5 Ratio, 1.25” Window, 3 CTs CT800K – 800/5 Ratio, 2.06” Window, 3 CTs CT2000K – 2000/5 Ratio, 3.00” Window, 3 CTs

CT Specifications:

Frequency: 50 to 400Hz; Insulation: 600 Volts, 10kV BIL Flexible Leads: UL 1015 105°C, CSA Approved, 24” Long, #16AWG

Software Option Numbers

Compliance Documents

Certificate of Calibration, Part #: CCal – This provides Certificate of Calibration with NIST traceable Test Data.

Current Transformer Kits

CT200K – 200/5 Ratio 1.00” Window 3 CTs

COMEXT3.1C – CommunicatorEXT 3.0 for Windows® (Single Lic) COMEXT3.MC – CommunicatorEXT 3.0 for Windows® (Multi Lic) * Consult factory application engineer for additional transformer ratios, types or window sizes.

E-Billing EXT™ – Automated bill generation software for Shark® 200-S Submeter only.